Page 15 - 吉多瑞KL乘用车精修工具

Kapitel01_EN.fm Seite 13 Donnerstag, 6. Mai 2021 10:54 10

KL-9002 SP E (Code 2909499)9) 9 件式 KL-9002 SP E
( 编码 290949
9 pcs.
弹簧压缩器，泡沫嵌入物
Spring Compressor, in a Foam Insert
Universally suitable for vehicles equipped with MacPherson Suspension/
普遍适用于配备麦弗逊弹簧支柱车桥和减震支柱车桥的车辆，尤其适用于全轮驱
Damper Struts. Ideal for All-Wheel-Drive vehicles, Transporters and Vans such
动汽车、厢式货车和面包车，如 Citroen Jumper；Fiat Ducato；Mercedes Vito、
as Citroën Jumper; Fiat Ducato; Mercedes Vito, V-Class, M-Class, W210 4Matic;
V 级、M 级、W210 4Matic；Peugeot Boxer，Break；Renault Master 等。
Peugeot Boxer, Break; Renault Master etc.
替代工具：W 203 589 01 31 00, 31 3 340, VAS 6046
Alternative tools: W 203 589 01 31 00, 31 3 340, VAS 6046
如果空间允许，也可以使用专门的弹簧架将横向转向架轴上的弹簧与设备一起拆
The use of special jaws will also enable coil springs mounted to wishbone suspensions to
卸和安装。
be removed and installed if space conditions allow.
Comes with pairs of jaws with protective inserts in size 1 and 2 designed for
包括 1 号和 2 号成对弹簧架，适用于 Ø 85 ( 内部 ) - 170 ( 外部 ) mm 的弹簧。
spring diameters of from 85 (inside) - 170 (outside) mm.
可提供用于 Ø 60 ( 内部 ) - 205 ( 外部 ) mm 弹簧的更多弹簧架。
Additional jaws for spring Ø of 60 (inside) - 205 (outside) mm are available as
最大负荷 27 500 N *
accessories.accessories.
* 在规定的 4 倍安全性下，弹簧压缩器的最大负荷为 27,500 N ！
Max. Load Capacity 27,500N *
* at the specified 4-times Safety Factor, the maximum load capacity of the spring compressor is
通用弹簧压缩器
27,500 N!
• 其中通过网格系统，最小跨度 ( 开口宽度 ) 可更改为 40 mm，最大跨度可更改为
The unique universal spring compressor
361 mm。这对于张紧非常短的弹簧 (2-3 个弹簧圈数 ) 和非常长的弹簧非常重要，
• which, due to a special latching system, allows the span (distance between jaws)
以便于其完全释放或更换。
to be adjusted from a minimum distance of 40mm to a maximum distance of
• 其中锻造弹簧架通过具有自动锁定功能的专利卡口锁定系统固定 ( 不需要工具、
361mm. This is an important feature when it comes to compressing very short
springs (2-3 coils) but also very long springs so as to allow all these to be fully de-
螺钉和螺丝环 )。
compressed and/or replaced. (e.g.on Audi, BMW, Fiat, Ford, Lancia, Mazda,
• 其中，当锁定销被剪断时，主轴驱动保持关闭。然后，可以通过辅助驱动器释
Mercedes, Renault etc.);
放张紧的弹簧，以便安装新的锁定销。
• which features a patented Bayonet Interlock System with an automatic self-
• 其中，当达到最大工作行程时，可通过自动空转防止释放过程中的主轴过载。
locking mechanism designed to safely fix the forged jaws to the compressor body
重要的是避免损坏弹簧压缩器。
(no tools, bolts or locking rings required);
• 其中，塑料保护插件可以拧到弹簧架上，以保护弹簧漆面。重要的是防止由缺
• whose spindle drive remains closed if the safety pin shears off. Thanks to the
口和腐蚀引起的弹簧断裂。
auxiliary drive, the compressed spring can then be decompressed to enable a new
• 由于具有多种弹簧架，因此几乎可用于所有麦弗逊弹簧支承轴、减震支承轴，
safety pin to be installed;
甚至还可用于横向转向架轴。
• which is equipped with an automatic freewheel designed to prevent the spindle
from overload during the decompression process once the maximum end of travel
由于高精度单个组件的相互作用和耐磨氮化钢的使用，液压缸工作非常平稳且几
has been reached - thus eliminating the risk of damage to the spring compressor;
乎没有磨损。例如，在张紧 Mercedes M 级车弹簧时，当锁定力约为 18,000 N 时，
• which enables the plastic protective inserts protecting the coating of the spring to
只需要 35 Nm 的驱动力。
be screw-connected to the jaws. This is very important to prevent spring failure/
breakage caused by notches and corrosion;
存储系统：KL-4999-1395 – 带有泡沫填充框架工具箱
• which is suitable for almost any MacPherson suspension/damper strut systems, as well
技术参数 :
as for many other wishbone suspensions - thanks to a wide range of jaws available.
液压缸 KL-9002-100：
Thanks to the interaction of special high-precision components and the use of wear-
475 mm
最小总长：
最小长度
resistant nitrided steel, the compressor body not only is smooth-running but also
最大总长：
最大长度
highly resistant to wear and tear. 715 mm
活塞工作行程：
305 mm
A
To compress a spring having a coil-bound force of approx. 18,000N (for example of a
主轴空转：
SPF
Mercedes M-Class) a torque of only 35Nm is required. 735 mm
最小跨度 I 最小跨度 (I) 开口宽度： 40 mm
Recommended Accessory: KL-4999-1395 Plastic Storage Case 72 mm
最小跨度 II
最小跨度 (II) 开口宽度：
最大跨度 I
Technical Data: 最大跨度 (I) 开口宽度： 328 mm
最大跨度 II 最大跨度 (II) 开口宽度： 361 mm
Base body
最大负荷（4 倍安全性时）：
475mm
L min. Minimum overall length 27 500 N
断裂极限：
715mm
L max. Maximum overall length 110 000 N
主轴驱动：
305mm
A Working Travel (piston stroke) SW 24
液压缸重量：
735mm
SPF Spindle freewheel at 6.9 kg
带 1 号和 2 号弹簧架的液压缸重量：
S min. I Minimum span (I) (distance between jaws) 13.4 kg
40mm
S min. II Minimum span (II) (distance between jaws) 72mm
供货范围： Maximum span (I) (distance between jaws) 328mm
S max. I
KL-9002 SP E - 带泡沫嵌入物的弹簧压缩器 361mm
S max. II
Maximum span (II) (distance between jaws)
Advantages:
描述
产品编号 Maximum load capacity (at 4-times safety factor) 27,500N 数量 优点：
KL-9002-100 Breaking point 110,000N 1 • 具有高张紧力，但操作仍然十分方便
液压缸
• Jaw-mounting device with automatic self-locking mechanism.
带保护插件的规格 1 号成对弹簧架
KL-9001-11 SP Spindle drive 24mm waf 1 • 带自动锁定功能的弹簧架固定
• Adjustable jaw-opening device.
带保护插件的规格 2 号成对弹簧架
KL-9001-12 SP Weight of compressor base body 6.9kg 1 • 跨度调整
• Drive features an additional auxiliary drive.
泡沫嵌入物
KL-4999-1322 Weight of compressor base body with jaws size 1 and 2 13.4kg 1 • 带附加辅助驱动器的驱动器
• Automatic free-wheel of the spindle.
• Also suitable for use on conical springs.
• 主轴的自动空转
Scope of Delivery: KL-9002 SP E Spring Compressor, in a Foam Insert • 也可用于锥形弹簧
• Comes with plastic protective inserts.
KL-9002 - 弹簧压缩器
Part No.
Description
类似于 KL-9002 SP E，但是不带保护插件和泡沫嵌入物 Qty • 包括塑料保护插件
KL-9002-100 Compressor Base Body 1 Note:
For the storage of the foam insert in the Modulo Workstation, the
KL-9001-11 SP Pair of Jaws in size 1, with Protective Inserts 1 提示：
KL-4999-1325 drawer insert adaptor will be needed.
KL-9001-12 SP Pair of Jaws in size 2, with Protective Inserts 1 要在Modulo台车上使用插件，需要KL-4999-1325插件适配器。
KL-4999-1322 Foam Insert 1
Note:
提示：
Additional jaws for springs with a Ø of from 60 (inside) to 205
KL-9002 Spring Compressor 可提供用于 Ø 60（内部）- 205（外部）mm 弹簧的更多弹簧架。
Like the KL-9002 SP, however, supplied without plastic protective inserts (outside) mm are available as accessories.
Copyright GEDORE Automotive GmbH, Germany, 10.E1 formerly 13