Page 62 - 吉多瑞KL乘用车精修工具

Kapitel02_EN.fm Seite 60 Donnerstag, 6. Mai 2021 10:55 10
2. 汽车底盘维修
2. Axle Repair
2.3 Wheel Bearings, Wheel Hubs and Drive Shaft
2.3 轮毂轴承 / 轮毂，万向轴
KL-0174-371 (Code 3069680)
KL-0174-371
( 编码 3069680)
12 件式
12 pcs.
Ford Transit 轮毂轴承拆卸工具套装
Puller Plate Kit, Ford Transit
Applicable to Ford Transit vehicles (model year 2006-2013 + model year 2014-..)
适用于 Ford Transit/Tourneo 的后桥和前桥 ( 制造年份：2000-2006 / 2006-2014
equipped with front-wheel drive. Suitable for use on front and rear axle (with
/2014-..) 带前轮驱动以及轮毂孔圆直径为 160 mm。
pitch circle Ø of 160mm).
轮毂轴承拆卸工具套装可以从后桥的枢轴将卡住的带制动盘的的轮毂向下压，以
The hole disc set allows you to quickly and professionally pull a fix wheel hub with
及将卡住的球头从前桥的轮毂中压出。例如在更换后桥的轮毂轴承和制动盘时需
brake disc from the kingpin at the rear axle as well as pressing a fix U shaft out of the
要用到，因为这些部件位于轮毂后侧。
wheel hub at the front axle. This is for example necessary for renewing the wheel
bearing and the brake disc at the rear axle, because these are situated behind the
所需驱动配件 ( 参见驱动一章 )：
wheel hub. Any work can be carried out directly on the vehicle within a few minutes.
KL-0040-2800 - 液压缸 28 t，KL-0215-35 M28 - 液压泵，
Necessary Drive Parts (cf. Chapter Drives):
KL-0040-2812-1 - 拉杆 / 压紧螺杆 M24x590，KL-0040-2812-5 - 夹紧螺母 M24，
KL-0040-2800 Hydraulic Cylinder (28t), KL-0215-35 M28 Hydraulic Pump,
KL-0174-3701 - 短型压件
KL-0040-2812-1 Pull/Pressure Spindle (M24x590), KL-0040-2812-5 Pressure Nut (M24),
供货范围：KL-0174-371 - Ford Transit 轮毂轴承拆卸工具套装
KL-0174-3701 Pressure Piece (short)
产品编号
描述
Scope of Delivery: KL-0174-371 Puller Plate Kit, Ford Transit 数量
KL-0174-330 3 号支撑盘 1
Part No. Description Qty
M 型牵引螺栓，M14 (l=100)
KL-0174-767
KL-0174-330 Puller Plate, Size 3 1 5
KL-0174-701
SK 凸肩螺母 M14
KL-0174-767 Puller Bolt, Type M, M14 (l=100) 5 5 1
适配器 2¼" 转 2¾", 28 t
KL-0174-572
KL-0174-701 Hex Shoulder Nut, M14 5
KL-0174-572 Adaptor, 2¼" to 2¾", 28t 1
KL-0174-372 (Code 3292762)2)
KL-0174-372
( 编码 329276
12 件式
12 pcs.
封闭式轮毂轴承补充套件 Ford Transit
Supplementary Kit for Closed Wheel
Bearings, Ford Transit
适用于 Ford Transit/Tourneo 的前桥 ( 制造年份 2006-2014 /2014-..) 带后轮驱动
以及制动盘紧固螺钉上的孔圆直径为 97.5 mm 和 111 mm。特别适用于前桥上带
Fits with the front axle on Ford Trans-it/Tourneo (2006-2014 / 2014 onwards)
有封闭式无中心孔的轮毂轴承单元的车辆。
with rear-wheel drive and a pitch circle Ø of 97.5mm and 111mm of the brake
借助补充套件，特别是在封闭式无中心孔的轮毂轴承上，可以快速和通过符合规
disc fixing screws. Particularly suitable for vehicles with wheel bearing units
without centre bore in closed design on the front axle.
范的方式拆卸前桥上带有轮毂和制动盘的螺栓连接的轮毂轴承单元，然后拆卸并
This supplementary kit enables quick and professional removal of the bolted wheel
压入轮毂轴承单元上的轮毂。这在更换轮毂轴承和制动盘时是必需的，因为它们
bearing unit with wheel hub and brake disc on the front axle, as well as subsequent
位于轮毂后面。所有操作都可以在几分钟内直接在车辆上完成。不需要费时地拆
removal and insertion of the wheel hub on the wheel bearing unit, [3:especially for
卸和安装轮毂轴承外壳，以及由此产生的轮轴校调。
closed wheel bearings without centre bore]. For example, this is required when
所需工具组 + 驱动配件：
replacing the wheel bearing and brake discs, as these are located behind the wheel
KL-0174-370 - Ford Transit 轮毂轴承提取器套装，
hub. All work can be carried out directly on the vehicle within a few minutes. Time-
KL-0040-2800 - 液压缸 28 t，
consuming removal and installation of the wheel bearing housing and a subsequent
wheel alignment are not necessary.
KL-0215-35 M28 - 液压泵
Scope of Delivery: Supplementary Kit for Closed Wheel Bearings, Ford Transit
供货范围：KL-0174-372 - Ford Transit 封闭式轮毂轴承补充套件
Part No. Description Qty
数量
描述
产品编号
Required Set of Tools + Drive Parts: KL-0040-8501 A Thrust ring 1 1
压环
KL-0040-8501 A
KL-0174-371 Puller Plate Kit, KL-0040-2812-1 Spindle M24, KL-0040-8621 Thrust adapter 1 1
压力适配器
KL-0040-8621
KL-0040-2812-5 Pressure Nut, KL-0174-3701 Pressure Piece, KL-0039-1823-4 Cap screw M10 x 12 5 5
圆柱头螺钉 M10 x 12
KL-0039-1823-4
KL-0040-2800 Hydraulic Cyl. (28t), KL-0215-35 M28 Hydr. Pump KL-0186-9000-3 Cap screw M10x75 5 5
圆柱头螺钉 M10x75
KL-0186-9000-3
KL-0174-513 (Code 2404311)
KL-0174-513
( 编码 2404311)
适配器 M42x2 转 M16x1.5
Adaptor, M42x2 to M16x1.5
用于组装 KL-0174-... 拉拔器系列的拉拔器的单个零件
Component for the assembly of a Puller from the KL-0174-...Puller-Series.
KL-0174-545 (Code 1920685)
KL-0174-545
( 编码 1920685)
Adaptor, 2 1/4"-14 UNS to M18
适配器 2 1/4"-14 UNS 转 M18
Component for the assembly of a Puller from the KL-0174-...Puller-Series.
用于组装 KL-0174-... 拉拔器系列的拉拔器的单个零件
KL-0174-547 (Code 1878123)3)
KL-0174-547
( 编码 187812
适配器 2 1/4"-14 UNS 转 M20x2
Adaptor, 2 1/4"-14 UNS to M20x2
用于组装 KL-0174-... 拉拔器系列的拉拔器的单个零件
Component for the assembly of a Puller from the KL-0174-...Puller-Series.
60 Copyright GEDORE Automotive GmbH, Germany, 10.E1 formerly